Custom Thermoelectric - Peltier

TXL TEG Installation

 


Thermoelectric (Seebeck) Power generation modules or TEGs have a large thermal expansion (and contraction) through the range of allowable temperatures -60ºC through the maximum rated temperature.  It is vitally important that the mounting system allow for this expansion and contraction while maintaining an even pressure on the module. 


Hot and Cold Side Identification:

Thermoelectric (Seebeck devices or TEGs) generators will only generate electricity if there is a temperature difference across the module.  That means that the “cold” side must be at least colder than the “hot” side for there to be any power generation.  The hot side is generally attached to a source of heat while the cold side is typically connected to a heat sink that is air or liquid cooled (water block). 

NOTE: Keep in mind that the heat from the hot side must travel through the TEG to the cold side in order for there to be electricity generated.  It is vitally important that the heat sink on the cold is able to quickly get rid of this heat in order to stay cool. If the cold side cannot get rid of this heat then it will not be the cold side for very long. Use of a Water Block or liquid heat exchanger will significantly increase heat dissipation thereby increasing power generation.

Examine the diagram below.  The view is seen as if the module is placed on a table in front of you as shown with the wires pointing towards you.  The red wire should be to the right, the black wire to the left.  The face that is pointing up (the face you see) is the hot face and should be mounted so it is in contact with the heat source.  The face that is pointing down (against the table) is the cold face and should be mounted in contact with the heat sink or water block to absorb any heat passing through the TEG.

image of TEG showing hot and cold sides

 

Temperature Limits 
The TXL TEG module can work continuously at temperatures up to the maximum temperature listed on the data sheet.  It is important that you do not allow any part of the TXL TEG to exceed this temperature.  Exceeding this temperature will cause irreversible TEG damage and failure.

 


Thermal Interface:

A Microscopic Look at Surfaces Even when you have two “flat and smooth” surfaces, they are far from truly flat or smooth.  The diagram below shows what’s really going on at a microscopic scale.

image of two surfaces magnified showing actual rough conditions

As you can see, the two surfaces may look flat and smooth, but in reality, when examined under magnification, they consist of “hills”, “peaks”, and “valleys”.  When these two surfaces are brought into contact with one another, only the peaks make contact.  It has been calculated that the average amount of contact between any two smooth surfaces is in reality only 5%. The other 95% are voids!

image of two surfaces magnified showing actual rough conditions

image of two surfaces magnified showing actual rough conditions

The above image shows how the remaining valleys create voids through which heat energy can barely pass through, in effect creating an insulated area – not the ideal thermal interface.

Surface Finish and Preparation
As a minimum, any surface intended to be part of a thermal interface should be flat to +/- 0.001 inches over the entire interface surface and smooth to a surface finish of 32 micro inches or better.

If possible, a polished surface is better since it ultimately reduces the size and depth of the “peaks” and “valleys”.  A polished surface finish of #6 to #8 is good, but the economics of polishing may determine a different stopping point for your product. If polishing is used, make sure to remove all polishing residues – see cleaning below.

The interface surface must be thoroughly cleaned, once all machining and polishing is completed.  Ultrasonic cleaning first in a heated degreaser solution and then in a solvent such as acetone is highly recommended to remove all oils and debris.  (Never place a TEG or Peltier device in an ultrasonic cleaner!) Do not touch the surface with bare hands (skin oils) or allow any contact with other materials.  It is better to complete this final cleaning stage just before assembly so as to minimize any dust or contamination.

Thermal Interface Materials (TIM)
Use a Thermal Interface Material (TIM) on both sides of the TEG.  You can use either a Thermal Grease or a Thermal Sheet.  Please see our TIM products under Products>Thermal Interface Materials.

The purpose of the TIM is to fill the valleys and gaps with a compressible material that has a much higher thermal conductivity (ability to transfer heat) than the air gaps it replaces.  This essentially makes the entire interface transfer heat instead of just where the peaks were contacting.  The following image shows how the situation has been dramatically improved.

image of two surfaces magnified showing how a TIM improves the heat flow

 


TEG Mounting:

TEGs should be mounted using the compression method.  That is, the TEG is compressed between a hot plate and a heat sink (or water block) that will be cooler.  The compression or clamping should be created with stainless steel machine screws on either side of the TEG.  See Exploded View and Section View images below.

image of two surfaces magnified showing actual rough conditions

image of two surfaces magnified showing actual rough conditions

Clamping Forces:
The following table lists the clamping forces required for optimum power generation and thermal contact.

 
TEG Size Pressure Total force per TEG Torque per Screw
30 x 30 mm
690 kPa (100 PSI)
64 Kg (140 lbs)
See Formula Below
40 x 40 mm
690 kPa (100 PSI)
112 Kg (248 lbs)
50 x 50 mm
690 kPa (100 PSI)
176 Kg (388 lbs)
56 x 56 mm
690 kPa (100 PSI)
220 Kg (486 lbs)
62 x 62 mm
690 kPa (100 PSI)
270 Kg (596 lbs)

Torque per screw can be approximated using the following formula;

Torque per Screw (inch–lbs) = (0.2) X (Screw Diameter) X (Pressure) X (TEG Surface Area)
                                                                    (Number of Screws)

Unified Screw Threads
 
Metric Threads
Screw Size
Screw Diameter
 
Screw Size
Screw Diameter
4-40
0.112
 
M2.5 x 0.5
2.48 (.098”)
6-32
0.138
 
M3 x 0.5
2.98 (.117”)
8-32
0.164
 
M4 x 0.7
3.978 (.157”)
8-36
0.164
 
M5 x 0.8
4.976 (.196”)
10-24
0.190
 
M6 x 1.0
5.974 (.235”)
10-32
0.190
     

Screw Position:
Locate bolt holes in your assembly such that they are at opposite sides of the center of the TEC between 1.0 mm to 12.7 mm (0.04 to 0.5 inches) from the sides of the TEC. [See first image below] The bolt holes should be in the same plane line as the fins to minimize any heat sink bowing (bending) that might occur.

Image showing how to properly load an assembly before tightening screwsimage showing how a TEC or TEG is crushed by tightening the screws too much on one side

Clamping Procedure:
Before tightening the screws, apply a light load/force in line with the center of the TEG by using a clamp or weights. Make sure the clamp or weights apply the force evenly and at the center.  Bolt carefully, by applying torque (tightening the screws) in small increments, and alternating between screws.  It is of the utmost importance that the screws are tightened evenly in small increments back and forth. If one screw is over tightened, then the tightening of the second screw may crush the TEG. [See 2nd image above] Use a torque limiting screwdriver for best accuracy. Check torque after 1-2 hours and retighten as needed. Repeat this check and tightening procedure again after several hours of actual use.

NOTE:
If a torque screwdriver is not available, a reasonably accurate pull spring scale* attached to the end of an L-shaped hex (Allen) wrench (this is a good reason to use socket head cap screws) can be used to determine when the screw torque is reached. Make sure the spring scale is pulled perpendicular (90°) to the Allen (Hex) Wrench at all times.

image showing alternative method of calculating torque for tightening screwtop view of showing how to calculate torque on a screw without a torque screwdriver

To calculate the required spring scale pull force, use this formula:

F = T / D

F = Force (lbs)
T = Torque (inch-lbs)
D = Distance (inches)

Example: What is the spring scale pull force required at the end of a 3.75 inch long L-shaped hex wrench to produce a 24 in-lbs screw torque setting?

F = 24 in-lbs / 3.75 in = 6.4 lbs pull force

[* Test the accuracy of the pull spring scale by hanging a known weight from the scale and adjust as needed]